Onsite Printer Service is #1 HP Printer Repair & Service company in Downtown Los Angeles. Fast onsite same-day repair on HP Printers in Downtown Los Angeles . Free Travel Free cleaning ! Authorized HP Printer Repair Center
ONSITE Printer Services Offers
- HP Authorized On Site LaserJet Printer & Design Jet Plotter Repair Service
- HP Certified Technicians
- 90% to 100% 1st Time Fix Rate
- Same Day Response with No Travel charge
- Free Cleaning with every HP & Canon Laser Printer Repair
- HP LaserJet Printer Repair Service
- HP Color Laser Jet Printer Repair Service
- HP MFP Laser Printer Repair Service
- HP Design Jet Plotter Repair Service
HP LaserJet Printer Maintenance & Cleaning
When your HP Laser Printer is making smudges, white lines and has paper jams our technician can simply clean your printer. Of course, the real benefit of cleaning is that it saves you money by prolonging the life of your printer!
- Removing the internal paper trays.
- Removing the toner cartridge.
- Clean inside the toner cavity with a dry, lint-free cloth and printer brush.
- Clean the printer mirror gently with the brush.
- Wiping away dust and spilled toner. Removing paper fragments.
- Cleaning the rollers.
- Cleaning the outside of the printer.
HP LaserJet – Troubleshoot 50.xx (fuser failure) messages
- 00 = Generic Fuser error
- 10 = Low Fuser temperature error
- 20 = Slow fuser error
- 30 = High fuser temperature error
- 70 = Fuser open error
Paper Jam in Printer
- Wrong ways to filling paper Tray
- Not selecting the Printer page setting
- Loading of papers
- Wrong Size of paper using in printing
- using the bad quality paper for printing
- Using the Dirty or Twisted paper
- Paper tray dirty with dust particles
13.XX PAPER JAM [LOCATION] Media is jammed at the specified location (and possibly at other locations). If the message persists after all jams have been cleared, a sensor or sensor lever might be stuck or broken. For all jam messages, do the following: 1. Remove jammed print media from the specified location. Check the entire paper path for other pieces of media in the path. 2. Open and close the top cover to clear the message. 3. Check sensors and flags in the paper path for proper operation.
3.0 PAPER JAM [LOCATION] A non-specific paper jam occurred. 1. Remove jammed media from the specified location. 2. Verify the paper tray is fully closed. 3. Inspect and/or replace the feed and separation rollers. 4. Ensure there is no obstruction in the path, such as a torn piece of paper. 5. Open and close the top cover to clear the message. 6. Check sensors and flags for proper operation.
13.1 PAPER JAM OPEN INPUT TRAYS Paper-delay jam at paperfeed area. 1. Ensure that paper trays are loaded and adjusted properly so media can feed from the tray. It might be necessary to reduce the stack height of media in the tray. 2. Check the input area for obstructions such as media in the path. Also, check to see if the registration assembly damaged or unseated. 3. Replace any defective sensors or flags. 4. Verify the media meets the specifications. 5. Check the pickup feed and separation rollers for unusual wear. Replace as needed. 6. Rotate the media in the input tray by 180° and/or turn it over On NX engines this is most likely the fuser flag or the ACPM. The ACPM has a photosensor hard-wired to the back of it.
13.10 PAPER JAM CHECK DUPLEXER Jam at duplexer. 1. Check the duplexer and the rear area of the printer for obstructions or damage. 2. Check the duplexer for proper operation. Replace the duplexer if a sensor is defective. On a 5si, 8000, or 8100 series laserjet a Duplex Jam can be caused by a tray 2 and 3 feed assembly failure.
13.14 For Laserjet 5si. This error is caused by a defective paper control PCA Replace paper control PCA.
13.2 PAPER JAM OPEN INPUT TRAYS Paper-stopped jam at paper-feed area. 1. Check the input area for obstructions such as paper in the path. Also check to see if the registration assembly is damaged or if the transfer roller is out of place. 2. Replace any defective sensors or flags. 3. Ensure the media does not exceed the maximum length. 4. If multiple sheets are feeding, it might be necessary to fan the media and reduce the stack height. Also, replace the separation pad. 5. Verify that the fuser is properly installed. On NX engines this is an input jam.
13.20 PAPER JAM CHECK REAR DOOR Media stopped in the paper path during power on or when the top door was closed. 1. Remove all media in the paper path, and then open and close the top cover. 2. If the message persists after all media is removed: Check if media is jammed in the prefeed area. Replace any defective sensors or flags
13.21 DOOR OPEN JAM The top cover was open while printing. 1. Clear the jam and close the top door. 2. If the message persists, check the top door switch for proper operation.
13.5 PAPER JAM CHECK REAR DOOR Paper-delay jam at fuser. 1. Check the transfer roller and small media belt to ensure they are operating and can feed print media. 2. Check the paper path for obstructions at the transfer roller, toner cartridge, paper feed assembly, and fuser. 3. Replace any defective sensors or flags. 4. Turn the media stack over and/ or rotate it by 180° in the input tray. If still persists – replace fuser, then DC controller.
13.6 PAPER JAM CHECK REAR DOOR Paper-stopped jam at fuser. 1. Check the paper path for obstructions at the fuser and output/delivery area. 3. Replace any defective sensors or flags.
13.99 PAPER JAM [LOCATION] A non-specific paper jam occurred. 1. Remove jammed media from the specified location. 2. Verify the paper tray is fully closed. 3. Inspect and/or replace the feed and separation rollers. 4. Ensure there is no obstruction in the path, such as a torn piece of paper. 5. Open and close the top cover to clear the message. 6. Check sensors and flags for proper operation
HP LaserJet Printer Parts Replacement
- Maintenance Kits
- Transfer Belts
- Printer Formatter Boards
- Laser Printers
- Engine DC Controllers
- Printer Control Panels
- Registration Assembly